Character Falls Through the Floor When First Spawned in UE5 (Causes and Fixes)

Table of Contents

Works in Unreal Engine 5.0 to 5.8. Updated November 2026.

Quick answer: the character spawns before there’s a floor to land on, or inside it.

  1. When the character starts, call Disable Movement on its Character Movement component so it can’t fall.
  2. When the level is ready, call Set Movement Mode with Walking (or Falling).
  3. Spawn the character a little above the ground, not at floor height.
  4. If it appears at 0,0,0 first, place a Player Start or override the GameMode’s spawn (see below).

Find your cause

What you seeLikely causeFix
Falls only on the first frames, or after a level loadsThe floor isn’t loaded yetDisable movement until it is
Falls when spawned at a saved locationSpawn point is inside or below the floorSpawn higher; use Try To Adjust Location, But Always Spawn
Appears at 0,0,0, then jumps to the right spotThe GameMode spawned its own pawnUse a Player Start or override the spawn
Always falls through one meshThe mesh has no collisionAdd collision to the mesh
UE 5.7: can’t land on spheres or curved surfacesReported engine bugSwap the sphere collision for a capsule

Fix 1: Freeze the character until the floor exists

With streamed levels, World Partition or a slow first load, the character can start falling before the ground has collision.

  1. In your character’s Event BeginPlay, drag in Character Movement and call Disable Movement.
  2. When your level is ready, call Set Movement Mode with New Movement Mode set to Walking. If you load levels yourself with Load Stream Level, do it from its Completed pin.

Possessing resets the movement mode. BeginPlay works for the character that exists when the level starts. If you spawn a character and Possess it later, call Disable Movement after the Possess node.

Fix 2: Don’t spawn inside the ground

An Actor’s location is the centre of its capsule, not its feet. Spawning at a floor point puts half the character underground, and it drops through.

  • Add the capsule’s half height (or about 100 units) to the spawn Z.
  • On Spawn Actor from Class, set Collision Handling Override to Try To Adjust Location, But Always Spawn.

Fix 3: Character appears at 0,0,0 first

The GameMode spawns its Default Pawn Class at a Player Start, or at the world origin if there is none. If you then move the character to a saved spot, it shows up at 0,0,0 first.

Pick one:

  • Place a Player Start in the level, from Window > Place Actors > Basic.
  • In your GameMode Blueprint, override Choose Player Start and return the actor to spawn at, such as your saved checkpoint.
  • Set Default Pawn Class to None and spawn and Possess the character yourself, so there’s only one.

Fix 4: The floor has no collision

Press the backtick key while playing and type show collision. If the floor shows no collision shape, open the mesh in the Static Mesh Editor, use the Collision menu (for example Add Box Simplified Collision) and save. Also check the floor actor’s Collision Presets isn’t set to NoCollision.

UE 5.7: infinite falling on spheres and curved surfaces

In 5.7, several users reported that a Character can’t land on a mesh with sphere collision and keeps falling or sliding off. The same scene worked in 5.6. The workaround that worked for them:

  1. Open the sphere mesh in the Static Mesh Editor.
  2. Remove the sphere collision and add Capsule Simplified Collision instead. A very short capsule is almost the same shape.

Setting the mesh’s Collision Complexity to Use Complex Collision As Simple also works, but costs more performance on high-poly meshes.

FAQ

Is adding a Delay before spawning a good fix?

It hides the problem on your PC and can fail on a slower one. Wait for the level to be ready instead.

My character falls forever. Where does it stop?

Below Kill Z in World Settings, the actor is destroyed.

Related articles